Comm Svr 1000 Upgrades to Rls.5.0 for Techs. Linux &
Questions, Answers, Braindumps (920-433)
Hi, passed, uses Study guides: Examcheats.net and course
manual. Here under are is my dump.
A customer is upgrading from a Meridian Option 11C to
a Communication Server (CS) 1000E Rls. 5.0 Standard
Availability. What happens to the Terminal Numbers (TNs)
during the upgrade?
A. The Small System (Card-Unit) TNs are retained.
B. The TNs are automatically converted to the Large
System format (Loop - Shelf - Card - Unit) for all assigned
C. The TNs are manually changed to the Large System
format (Loop - Shelf - Card - Unit) by reprogramming
all devices assigned TNs.
D. The TNs for only the IP Phones are automatically
converted to the Large System format (Loop - Shelf -
Card - Unit). All other devices assigned TN must be
CP-PM, IBM X306m and HP DL320-G4 are all platforms which
support the Signaling Server applications on Release
5.0. Which server comes with the software installed?
B. IBM X306m
C. HP DL320-G4
D. None of the servers
A customer is upgrading an existing Media Gateway 1000T
Rls. 4.5 with an expansion to a stand alone Communication
Server (CS) 1000E Rls. 5.0 with two IP Media Gateways
and a Signaling Server that is a Nortel ISP 1100. After
the installation, which should you do to verify that
there is sufficient memory to support the upgrade to
A. View the attributes of the Signaling Server using
B. Remove the cover from the ISP 1100 and look at the
label(s) on the DIMM board(s).
C. Boot the Signaling Server and monitor the startup
messages for configured memory.
D. Follow the procedure to verify successful memory
upgrade and look for the message 1 GByte OK, since 1
GB of memory is required in the ISP 1100.
A customer is upgrading from Meridian 1 Option 11C Rls.
24 to a Communication Server 1000E Rls. 5.0 Standard
Availability with a single Media Gateway 1000E chassis
and has decided to install a new CP-PM Call Server card.
Which step(s) are required to migrate a Small System
database to the CP-PM?
A. Complete an inventory of the Small System using LD
117 and then migrate using LD 10 and LD 11.
B. Backup the Small System database using LD 43 EDD
and then archive the database using LD 143.
C. Configure MGCONF and MGTDS separately and map them
to a specific CP-PM CS prior to migration.
D. Use the issp command in LD 22 to determine MGC Loadware
PEPS and then use the lwinst command to activate the
MGC Loadware patch.
A customer has upgraded to a Communication Server 1000E
Rls. 5.0 with the NTDW61, the new CP-PM Signaling Server.
They have been informed that this card can be inserted
into any slot of the Media Gateway 1000E or Media Gateway
1000B. Which slots support the NTDW61?
A. 0, 1, 2
B. 1, 2, 3
C. 1, 3, 0
D. 2, 3, 0
A customer is upgrading to a Communication Server 1000E
Rls. 5.0 and wants to use a COTS with Signaling Server
functionality to Rls. 4.5 since they are using the H.323
Gatekeeper. The customer does not want to deploy Enterprise
Common Manager (ECM). In this configuration, which COTS
should be configured?
A. COTS Server running LINUX
B. COTS Server running VxWorks
C. COTS Server running LINUX with CS 1000 Management
D. COTS Server running LINUX with NRS Redirect Services
A customer is upgrading to Communication Server (CS)
1000 Rls. 5.0 from a CS 1000E CP-PIV on Rls. 4.5. The
customer is requesting the least-cost upgrade solution.
What should be proposed?
A. Upgrade Call Server hardware and software.
B. Upgrade software and upgrade SS memory to 1 GB.
C. Upgrade processors to new CP-PM CS and upgrade software.
D. Upgrade CP-PIV CS to CP-PM CS, SS memory to 1 GB,
software and replace the SSC cards with Media Gateway
A customer is upgrading from a Communication Server
(CS) 1000S with one Media Gateway (MG) and one Media
Gateway Expander to a Communication Server 1000E Rls.
5.0 Standard Availability with a single Media Gateway
1000E chassis/expander. Which component must be replaced
in the MG 1000S to convert the CS 1000S to a CS 1000E?
A. SSC Card
B. Call Server
C. Voice Gateway Media Card
D. Nortel IPS 1100 Signaling Server