Communication Server 1000 Rls. 5.0 Upgrades for Technicians.
Exam Questions, Answers, Braindumps (920-333)
I had enjoyed the paper after getting help from the
dumps of www.brain-dumps.com. Here is my contribution.
A customer is upgrading from Meridian 1 Option 11C
Rls. 24 to a Communication Server 1000E Rls. 5.0 Standard
Availability with a single Media Gateway 1000E chassis
and has decided to install a new CP-PM Call Server
card. Which step(s) are required to migrate a Small
System database to the CP-PM?
A. Complete an inventory of the Small System
using LD 117 and then migrate using LD 10 and LD 11.
B. Backup the Small System database using LD 43 EDD
and then archive the database using LD 143.
C. Configure MGCONF and MGTDS separately and map them
to a specific CP-PM CS prior to migration.
D. Use the issp command in LD 22 to determine MGC
Loadware PEPS and then use the lwinst command to activate
the MGC Loadware patch.
A customer is upgrading to Communication Server (CS)
1000 Rls. 5.0 from a CS 1000E CP-PIV on Rls. 4.5.
The customer is requesting the least-cost upgrade
solution. What should be proposed?
A. Upgrade Call Server hardware and software.
B. Upgrade software and upgrade SS memory to 1 GB.
C. Upgrade processors to new CP-PM CS and upgrade
D. Upgrade CP-PIV CS to CP-PM CS, SS memory to 1 GB,
software and replace the SSC cards with Media Gateway
A customer has upgraded to Communication Server 1000E
Rls. 5.0 and is using the Management Tool NRSM on
Linux. In conducting a search for Routing Entries,
the engineer is looking for a specific number range.
The engineer wants to secure all entries from the
entire service domain and identify specific end points
where they terminate. What is a more efficient procedure
for searching for Routing Entries?
A. Enter the specific DN type + the entire
B. Enter *56* (considered a wild card) + the entire
C. Enter #56# (considered a wild card) + the entire
D. Enter the specific service domain + the entire
service domains to specific endpoints.
A customer is upgrading from a Meridian Option 11C
to Communication Server 1000E Rls. 5.0 with an IP
Media Gateway. With this configuration, they are using
both the 32-port and 96-port DSPs on the MGC. If they
need more DSPs, what is the available configuration
A. An MC32S can be added.
B. Change out the Low Density DSP to a second High
C. A second IPMG would need to be installed to provide
the additional DSPs.
D. The entire system would be to be re-engineered
to ensure timeslots are available for MGCONF and MGTDS
A customer is upgrading to a Communication Server
1000E Rls. 5.0. Which hardware components also provide
DSP services? (Choose two.)
A. 32-port DSP Daughterboard
B. 96-port DSP Daughterboard
C. 128-port DSP Daughterboard
D. Media Gateway Controller card (MC32B)
Answer: A, B
A customer is upgrading from Communication Server
1000E Rls. 5.0 Standard Availability to Communication
Server 1000E Rls. 5.0 High Availability. In addition
to a Media Gateway 1000E, what configuration must
be in place for this to occur?
A. A CP-PM and an MGC
B. A CP-PM CS, an MGC, and package 410 High Availability
C. A CP-PM CS, CP-PM SS, an MGC, and package 405 GRSEC
D. A CP-PM CS with either a CP-PM SS, ISP 1100 or
COTS VxWorks SS, and an MGC, and package 410 High
A customer is upgrading an existing Media Gateway
(MG) 1000T Rls. 4.5 to a Media Gateway 1000E Rls.
5.0 and wants to utilize media security through the
DSPs. This upgrade includes a Media Gateway Controller
(MGC) card with DSP daughterboards. What is the maximum
number of DSPs that can be equipped on an MGC using
32 or 96-port Daughterboards?
A customer is installing a Communication Server 1000E
Rls. 5.0 with a single Media Gateway 1000E chassis.
In this configuration, which slot houses the Media
Gateway Controller Card?
A. Slot 0
B. Slot 1
C. Slot 2
D. Slot 3 E. Slot 4