Communication Server 1000
Rls.5.0 Install & Commissioning
Questions, Answers, Braindumps (920-332)
These are Guaranteed question for this exam. I only
used www.exams.ws guide and i was succedded.
QUESTION 1: A customer has a Communication Server
(CS) 1000E system with a cost optimized gateway controller
and DSP daughterboards that support 96 VoIP voice
gateway resources. The CS 1000E supports CeMux PSTN
access cards in the Media Gateway 1000E, reducing
the overall cost and complexity of the system. Based
on these requirements, which is the recommended Rls.
5.0 hardware for the customer?
A. CP-PM Call Server and MGC with High-Density DSP
B. CP-PM Call Server, MGC without DSP Daughterboards,
and MC 32S
C. CP-PIV Call Server, MGC without DSP Daughterboards,
and MC 32S
D. CP-PM Call Server and Media Gateway Controller
(MGC) with Low-Density DSP Daughterboard
QUESTION 2: A customer has deployed a Communication
Server (CS) 1000E network with a primary and a secondary
site. In the event the primary system fails, the customer
requires the user database to be replicated from the
primary site to the secondary site. Which Geographic
Redundancy configuration meets the customers needs?
A. CPP Redundancy
B. Campus Redundancy
C. Controlled Load-sharing
D. Survivable Media Gateway
QUESTION 3: A customer has imported the node files
from the Signaling Server to the Call Server in Element
Manager. The customer sends the node configuration
files to all IP Telephony components in the node using
the Transfer/Status button. The Transfer/Status button
on the Transfer/Status web page is yellow. What does
A. The transfer status of the node is in progress.
B. The node configuration is transferred to the elements.
C. The transfer status of the node elements is unavailable.
D. An element within the node failed to transfer the
BOOTP or CONFIG files.
QUESTION 4: Upon opening the web browser to begin
the login process into Element Manager on a Communication
Server (CS) 1000E system, which two IP addresses can
you enter into the address bar of the web browser?
A. the Call Server IP address
B. the Signaling Server Node IP address
C. the Terminal Proxy Server (TPS) IP address
D. the Embedded LAN (ELAN) IP address of the Signaling
Answer: B, D
QUESTION 5: A customer has successfully installed
and configured a Signaling Server in a Communication
Server (CS) 1000E system. After configuration and
reboot, the Follower Signaling Server sends out BOOTP
requests and waits for a response. However, there
is no BOOTP response. Which action should be taken?
A. Reboot the Leader Signaling Server.
B. Wait for a BOOTP response from the Leader Signaling
C. Configure the IP Telephony node for the Follower
from Element Manager.
D. Configure the IP Telephony node for the Follower
from the Installation Tools menu.
QUESTION 6: You are installing software for the first
time on a new Communication Server (CS) 1000 Rls.5.0
Signal Server and receive the following message: The
filesystems verification failed! Which action should
you take next?
A. Troubleshoot the hardware failure.
B. Select the menu choice to abort the installation.
C. Contact the next level of support to help diagnose
D. Select the menu choice to partition and initialize
the hard disk.
QUESTION 7: Which software installation must be completed
before installing software on any Enterprise Media
Gateway in a Communication Server (CS) 1000 Rls. 5.0
A. The Call Server software must be installed or upgraded.
B. The IP telephone software must be available to
all IP telephones.
C. The ERS 8600 routing switches must be running the
latest software revision.
D. All Signaling Servers must be configured with the
newest version of software.
QUESTION 8: A customer is implementing a Communication
Server (CS) 1000 Rls.5.0 Communication Server 1000E
High Availability (HA) system. The customer wants
to know if there are any special package requirements
beyond the HA Package needed for the system. Which
two software packages are mandatory when deploying
a CS 1000E HA system? (Choose two.)
A. SBO - Branch Office Package 390
B. SOFTSWITCH. Soft Switch Package 402
C. IPMG. Media Gateway 1000E Package 403
D. SIP - SIP Gateway and Converged Desktop Package
Answer: B, C
QUESTION 9: A customer is installing a Media Gateway
Controller (MGC) in a Communication Server (CS) 1000E
system. The customer is connected to SDI 0 of the
MGC to access the configuration menu. No IP information
exists for the MGC. How does the customer get to the
mgcsetup menu to configure the MGC?
A. Type mgcsetup on the screen.
B. No action required. The MGC will boot directly
into the setup menu.
C. The prompt Press any key to stop auto-boot and
enter mgcsetup appears.
D. Enter a shell command. <CTRL>O<CTRL>A<CTRL>M,
provide OAM username and password to access OAM shell.