REAL QUESTIONS SUBMIT MATERIAL ADVERTISE
Braindumps

Microsoft

Cisco

Citrix

CIW

CompTia

CWNA

Apple

Adobe

HP

Legato

Exin

Filemaker

Brocade

Ericsson

TIA

Veritas

ISEB

SCP

IISFA

ISM

OMG

Apc

Mile2

Foundry

Huawei

McData

Symantec

TeraData

RedHat

Solar Winds

Blue Coat

Riverbed

 

 
 
Click on name of dumper to view the dump
 
Stefanie
 
 

 

Braindumps of 920-322
Succession 1000/1000M
Rls. 3.0 for Technicians

 

Exam Questions, Answers, Braindumps (920-322)

Hi to all and thanks to www.exams.ws and www.4exam.com But there’s no need to have it from both of them, only s from only one are sufficient I think. Here is my contribution.

1 Abc .com has a Succession 1000/1000M Rls. 3.0system. The system administrator wants to add CallPilot, which requires an Embedded LAN (ELAN) to be built in the Action Device and Number (ADAN) section of Overlay LD 17 Configuration. Assume there is NO Symposium Call Center. What is the normal range of device numbers?
A. 0-32
B. 16-31
C. 0-255 (user defined)
D. number range is determined by the placement of the card
Answer: B

2 Abc .com with a Succession 1000M Rls. 3.0 system wishes to use their Ethernet LAN to carry functional signaling traffic for their Call Center Server. How should the Succession Call Server ELAN IP address be configured?
A. The Succession Call Server ELAN NIC IP address must correspond to the Signaling Server IP address configured in LD 117, and must be in the same subnet as the VGMC(Voice Gateway Media Card).
B. The Succession Call Server ELAN NIC IP address must correspond to the active ELNK IP address shown in Load 137.
C. Use the Succession Call Server installation CD-ROM menu to configure the IP address the same as the Gatekeeper IP address.
D. The Succession Call Server ELAN NIC IP address must be configured in LD 117 to be unique in the system.
Answer: B

3 Abc .com wishes to grant a particular group of users access to a Succession 1000M 3.0 trunk group so that direct access is not automatically blacked for calls. Since the default value using Overlay LD 11 is set to automatically block direct access, what should the customer do to make the appropriate change?
A. Set trunk Group Access Restriction (TGAR) to any value that is not withen (0-31).
B. Leave the trunk Group Access Restriction (TGAR) empty.
C. Set trunk Group Access Restriction (TGAR) to a value of 1.
D. Set trunk Group Access Restriction (TGAR) to value other than 1.
Answer: D

4 On a Succession 1000M Rls. 3.0 system, which prompt is used to specify whether the direction of a trunk rout will be Incoming and/or Outgoing?
A. ICOG
B. ICNT
C. SIGL
D. DLTN
Answer: A

5 A large Succession 1000M Rls. 3.0 system uses Limited Access Passwords (LAPWs). The system administrator wants to expand the access for some passwords. What is required to modify this part of the Configuration Record (Overlay LD 17)?
A. PWD2
B. PWD1
C. Administrative password
D. Basic Authorization code
Answer: A

6 Abc .com has a Succession 1000M Rls. 3.0 system installed. They notice the error message: ERR9006 "Invalid ESRT configuration. ACCD intercept treatment has been given to the set "on the PBX terminal. What action should be taken to correct this error?
A. Correct the database
B. Restore the database
C. INI the switch
D. Reboot the switch
Answer: A

7 Abc .com is installing a Succession 1000M Rls. 3.0 system installed. They noticed error ERR4 143 data "cannot access NARS database?on the monitor. Which action should you take to correct this error?
A. Restore NARS database.
B. INI the switch.
C. Check NARS database for space.
D. Define ESN database for the customer.
Answer: D.

8 Abc .com has installed a Succession 1000 Rls. 3.0 system. They to configure Start Arrangement incoming (STRI) prompt as part of Trunk Data Block programming in LD 14. STRI determines witch type of signaling will be used by the trunk to initate digit sending or collection. The customer wants to program the system so the terminating trunk to initlate digit sending or collection. The customer wants to program the system so the terminating trunk is NOT expected to return a pulse telling the originating end to begin sending digits. What is the correct value for STRI prompt considering customer's request?
A. DDL
B. OWK
C. IMM
D. WINK
Answer: C

920-322


 

 

Braindumps Real exam questions and verified answers - 100% passing guarantee - cheap prices.

 

Free brain dumps Braindumps, notes, books for free

 

Braindumps and Exams - Instant download real exam questions - Passing guarantee.

Follow us on FaceBook
Braindumps on Facebook
 
 
 
 
 

CheckPoint

Linux

Novell

DB/2

Network Appliance

EC-Council

Nortel

McAfee

Juniper

ISACA

PMI

Sybase

EMC

HDI

SNIA

ISC

Sair

IBM

Lotus

Exam Express

3COM

BICSI

DeLL

Enterasys

Extreme Networks

Guidance Software

Computer Associates

Network General

SAS Institute

Alcatel Lucent

SeeBeyond

TruSecure

Polycom

Hyperion

Hitachi

Nokia

Fortinet

Vmware

Fujitsu

Tibco

Intel

PostgreSQLCE

BusinessObjects

RESSoftware

BlackBerry

AccessData

ICDL

Isilon

SAP

The Open Group

ACSM

Altiris

Avaya

Cognos

F5

Genesys

SDI

ACI

ASQ

Google

H3C

HIPAA

HRCI

SOA

IIBA

Zend